Deep Test Technology of Single-Edge Rigid Reamer for Deep Hole Processing

沈兴全; 孟庆义; 李耀明

您当前的位置：

首页 >

文章列表页 >

Deep Test Technology of Single-Edge Rigid Reamer for Deep Hole Processing

更新时间：2026-09-14

- Deep Test Technology of Single-Edge Rigid Reamer for Deep Hole Processing
- 深孔单刃刚性铰刀工艺试验研究
- Vol. 33, Issue 2, Pages: 107-110(2012)
- 作者机构：
  
  1. 中北大学山西省深孔加工工程技术研究中心
  2. 北京卫星制造厂
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Published：2012
- 稿件说明：
移动端阅览
沈兴全, 孟庆义, 李耀明. Deep Test Technology of Single-Edge Rigid Reamer for Deep Hole Processing[J]. 2012, 33(2): 107-110.
DOI：

沈兴全, 孟庆义, 李耀明. Deep Test Technology of Single-Edge Rigid Reamer for Deep Hole Processing[J]. 2012, 33(2): 107-110. DOI：

摘要

单刃刚性铰加工具有高速切削、自动导向、加工表面粗糙度低等一系列优点

本文利用弹、塑性理论

研究了作用于导向块的力对孔壁的挤压效果

提出了单刃刚性铰刀铰削加工的两种不同工作状态

分析了铰削加工处于挤压状态的条件.经试验分析

得出为了获得良好的孔加工表面质量

必须使铰削加工处于挤压工作状态

确定了切削参数对切削力及表面粗糙度的影响.

Abstract

Single-edge high-speed cutting rigid hinge processing is auto-oriented and of low surface roughness.The elastic and plastic theories were employed to study the force acting on the guide block and the compression effect on the pore wall.The single rigid blade reamer works at two different states.The extrusion conditions of the reamer was analyzed.It was concluded that in order to obtain good surface quality

the ream must be processed in extrusion reaming state.The corresponding cutting parameters

cutting force and surface roughness were determined.

关键词

Keywords

references

樊铁槟,裴宏伟.内排屑深孔钻导向条的合理设计和分布[J].工具技术,2009,31(9):25-27.

Deng C S,Chin J H.Hole roundness in deep-hole drilling as analysed by taguchi methods[J].International Journal of Advanced ManufacturingTechnoloy,2010,25(5-6):420-426.

Rau P,Shunmugam M S.Studies in boring tre-panning association drilling[J].Wear,2009,124(1):33-43.

Landers R,Ulsoy A.Chatter analysis of machining systems with nonlinear force process[J].ASME International Mechanical Engineering Congress and Exposition,Atlanta,Georgia,2010,58:183-190.

Chin J H,Jiang R J.Dynamic modeling and simulation of hydraulic-driven fight simufator under different controllers[C].Proceedings of the JASTED International Conference on Modeling,Simulation and Optimization,2010:52-56.

Weinert K,Webber O A.Experimental investigations of the dynamics of the BTA deep hole drilling process[J].Journal of Production Engineering-Research Development Germany,2009,45(2):925-935.

Messaoud A,Weihs C.Monitoring a deep hole drilling process by nonlinear time series modeling[J].Journal of Sound and Vibration,2009,321:620-630.

李伯民,赵波.现代磨削技术[M].北京:机械工业出版社,2009.

童慧芬.深孔加工中切削热的理论计算与温度场模拟[D].太原:中北大学,2009.

张志军,吴希平.深孔加工镗杆的结构模态对切削颤振的影响[J].机械设计与制造,2007(3):26-28.

郑建明,李言,肖继明,等.基于神经网络的多特征融合刀具磨损量识别[J].机械科学与技术,2009,21(1):111-113.

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Hopkinson Bar Pulse Width Extension Test Method Based on Polyurethane Wave Shaper

Research Progress on Machine Learning⁃Based Structural Design and Performance Characterization of Composites

High⁃Precision Photoeletric Coordinate Positioning Technology Based on Transformer⁃FPGA Collaborative Feature Modeling

A Meta⁃Learning and VAE⁃GAN Based META⁃VAEGAN⁃DNN Method for Network Intrusion Detection

机器人机构设计与控制专栏

Related Author

No data

Related Institution

No data

⁰