压痕诱导Zr65Al7.5Ni10Cu12.5Ag5非晶合金晶化动力学研究

马建生; 闫志杰; 胡勇

您当前的位置：

首页 >

文章列表页 >

压痕诱导Zr₆₅Al_7.5Ni₁₀Cu_12.5Ag₅非晶合金晶化动力学研究

更新时间：2026-09-14

- 压痕诱导Zr₆₅Al_7.5Ni₁₀Cu_12.5Ag₅非晶合金晶化动力学研究
- 压痕诱导Zr₆₅Al_7.5Ni₁₀Cu_12.5Ag₅非晶合金晶化动力学研究
- Issue 3, (2012)
- 作者机构：
  
  太原科技大学材料科学与工程学院
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Published：2012
- 稿件说明：
移动端阅览
马建生, 闫志杰, 胡勇. 压痕诱导Zr₆₅Al_7.5Ni₁₀Cu_12.5Ag₅非晶合金晶化动力学研究[J]. 2012, (3).
DOI：

马建生, 闫志杰, 胡勇. 压痕诱导Zr₆₅Al_7.5Ni₁₀Cu_12.5Ag₅非晶合金晶化动力学研究[J]. 2012, (3). DOI：

摘要

利用X射线衍射仪(XRD)

高分辨透射电镜(HRTEM)对Zr65Al7.5Ni10Cu12.5Ag5非晶合金Vickers压痕的微观结构变化进行了研究.在压头棱下方和压头尖端下方区域分别观察到了微米和纳米尺寸的晶粒析出.结合有限元模拟

分析了压应力对晶化过程中形核及晶核长大的影响.在压应力最大的尖端区域形核激活能最小

形核速率最大

需要的晶核长大激活能也最大.压应力越小形核速率越小

需要的晶核长大激活能越小.应力是影响非晶合金在塑性变形过程中发生晶化的动力学因素之一.

Abstract

X-ray diffraction(XRD) and high resolution transmission electron microscopy(HRTEM) were applied to investigate the microstructure changing during the Vickers indentation of the Zr65Al7.5Ni10Cu12.5Ag5 amorphous alloy.The results showed that the micro-sized crystals precipitated under the indenter edges and nano-sized crystals form under the indenter tip.The nucleation behaviors induced by indentation was investigated with help of the finite element simulation in the deformed regions.On the tip region with larger compressive stresses

the nucleation activation energy becomes much lower while the nucleation rate becomes considerably larger.The results show that the compressive stress is one of the most important factors influencing on the crystallization kinetics of an amorphous alloy during plastic deformation.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

速射火炮身管冲击载荷下内膛塑性变形分析

圆截面坯料拔长时空腔形成机理

Network Intrusion Detection Model Based on Recurrence Plot and MobileViT⁃AESTF

Research Progress on Machine Learning⁃Based Structural Design and Performance Characterization of Composites

机器人机构设计与控制专栏

Related Author

李强

李鹏辉

胡明

武云飞

茹占勇

李克智

Related Institution

中北大学机电工程学院

⁰