螺旋内肋管的流阻与换热特性实验研究

刘湘云; 史保新; 李克天; 刘吉安

您当前的位置：

首页 >

文章列表页 >

螺旋内肋管的流阻与换热特性实验研究

机械与动力工程 | 更新时间：2026-09-14

- 螺旋内肋管的流阻与换热特性实验研究
- Experimental Study of Flow Resistance and Heat Transfer Inside Internally Ribbed Tube
- 中北大学学报（自然科学版） 2010年31卷第2期页码：108-112
- 作者机构：
  
  1. 广东工业大学材料与能源学院
  2. 广东工业大学机电工程学院
- 作者简介：
- 基金信息：
  
  广东省粤港招投标资助项目(TC07BF09-3)
- DOI：
  中图分类号：
- 纸质出版：2010
- 稿件说明：
移动端阅览
刘湘云, 史保新, 李克天, 等. 螺旋内肋管的流阻与换热特性实验研究[J]. 中北大学学报（自然科学版）, 2010,31(2):108-112.

刘湘云, 史保新, 李克天, et al. Experimental Study of Flow Resistance and Heat Transfer Inside Internally Ribbed Tube[J]. 2010, 31(2): 108-112.
刘湘云, 史保新, 李克天, 等. 螺旋内肋管的流阻与换热特性实验研究[J]. 中北大学学报（自然科学版）, 2010,31(2):108-112. DOI：

刘湘云, 史保新, 李克天, et al. Experimental Study of Flow Resistance and Heat Transfer Inside Internally Ribbed Tube[J]. 2010, 31(2): 108-112. DOI：

摘要

用实验方法研究了定常状态下

不同的肋高度和不同肋条数对螺旋内肋铜管内的流阻和换热特性的影响.螺旋内肋铜管内径为7 mm

内肋高为0和0.22 mm

0.24 mm和0.25 mm

肋条数为44和60

雷诺数在900

500范围之内.以无螺旋肋的光滑铜管作为基准

研究了螺旋内肋高和螺旋条数对换热效果及阻力的影响.结果表明:有螺旋肋的管内换热都得到了增强;螺旋肋高度为0.25 mm的铜管的换热效果明显大于其它两种肋高管的换热效果

肋高为0.22 mm和0.24 mm的内肋铜管的换热效果相当;肋的高度对阻力系数的影响却是随着肋高的增大而增大.螺旋肋的条数越大

阻力越大

换热效果也越好.

Abstract

The heat transfer characteristics and flow resistances in internally ribbed copper tubes with different rib heights and pitches were experimentally studied in steady state.The comparison of the heat transfer effect was made among four tubes with different rib heights.The inner diameter of the copper tube is 7 mm

the relative rib heights are 0 mm

0.22 mm

0.24 mm

and 0.25 mm

the relative rib pitches are 44 and 60.The Reynolds number varies from 900 to 6 500.Analysis of the experimental results may lead to the following conclusions: The presence of ribs enhanced the heat transfer greatly.The influence of the rib heights on the heat transfer is monotone

and the flow resistance increases with the increasing of rib heights and rib pitches.

关键词

Keywords

references

刘湘云,丁水汀,陶智,等.不同肋间距变截面回转通道内流阻与换热特性[J].航空动力学报,2004,19(4):640-644.Liu Xiangyun,Ding Shuiting,Tao Zhi,et al.Characteristics of flow and heat transfer inside various cross-sectionchannel with different rib pitches[J].Hangkong Dongle Xuebao,2004,19(4):640-644.(in Chinese)

潘志勇.内螺纹铜管生产及发展趋势[J].湖南有色金属,2003,19(50):28-29.Pan Zhiyong.The production and development tendency of inner 2 grooved copper tube[J].Hunan Nonferrous Met-als,2003,19(50):28-29.(in Chinese)

Garimella S,Christensen R N.Heat transfer and pressure drop characteristics of spirally fluted annul Part-heattransfer[J].Heat Transfer,1995,117(1):61-68.

杜学峰,张晓春,王彦坤,等.ACR铜管在空调换热器中的应用与发展[J].平原大学学报,2003,20(4):12-13.Du Xuefeng,Zhang Xiaochun,Wang Yankun,et al.Application and development of the ACR copper tube in the airconditioner heat exchanger[J].Journal of Pingyuan University,2003,20(4):12-13.(in Chinese)

孙东亮,樊菊芳,王良璧.内螺纹肋管内流动与换热的数值模拟[J].工程热物理学报,2005,26(3):483-485.Sun Dongliang,Fan Jufang,Wang Liangbi.Numerical study of fluid flow and heat transfer in helically ribbed tubes[J].Journal of Engineering Thermalphysics,2005,26(3):483-485.(in Chinese)

张政,张建文.螺旋内槽管内的层流流动与传热的数值模拟[J].高校化学工程学报,1995,9(2):125-128.Zhang Zheng,Zhang Jianwen.Numerical simulation of laminar fluid flow and heat transfer in spiral internally finnedtube[J].Journal of Chemical Engineering of Chinese Universities,1995,9(2):125-128.(in Chinese)

张建文,张政.螺旋内翅片管内充分发展流体流动与传热的数值模拟分析[J].高校化学工程学报,1999,13(2):114-120.Zhang Jianwen,Zhang Zheng.Numerical simulation of fully developed fluid flow and heat transfer in a spiral finnedtube[J].Journal of Chemical Engineering of Chinese Universities,1999,13(2):114-120.(in Chinese)

宫武旗,李新宏,黄淑娟.沟槽壁面减阻机理实验研究[J].工程热物理学报,2002,23(5):579-582.Gong Wuqi,Li Xinhong,Huang Shujuan.Experiment study on the mechanism of riblets drag reduction[J].Journalof Engineering Thermophysics,2002,23(5):579-582.(in Chinese)

程立新,陈听宽.煤油在内螺纹管中流动沸腾强化传热特性[J].化工学报,2000,51(1):52-56.Cheng Lixin,Chen Tingkuan.Characteristics of enhancement of flow boiling heat transfer with kerosene inside inter-nally ribbed tube[J].Journal of Chemical Industry and Engineering,2000,51(1):52-56.(in Chinese)

桑希前,唐永立,李风丽,等.瘦齿型内螺纹铜管传热性能试验分析[J].制冷空调,2004,4(5):78-81.Sang Xiqian,Tang Yongli,Li Fengli,et al.The analysis of heat transfer capability of the new type inner 2 groovedcopper tube with the slimmer fin[J].Refrigeration and Air-Conditioning,2004,4(5):78-81.(in Chinese)

浏览量

285

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

基于元学习与VAE⁃GAN的META⁃VAEGAN⁃DNN网络入侵检测方法

《中北大学学报(自然科学版》》征稿简则

基于Transformer⁃FPGA协同特征建模的光电坐标高精度定位技术

OFDM中基于DFT的自适应信道估计算法

基于低分子质量PEI的类PEG聚合物基因载体