板带冷轧过程三维弹塑性有限元模拟

张雅琴; 何宗霖; 张雪娜

您当前的位置：

首页 >

文章列表页 >

板带冷轧过程三维弹塑性有限元模拟

材料科学与工程 | 更新时间：2026-09-14

- 板带冷轧过程三维弹塑性有限元模拟
- Three-Dimensional Elastic-Plastic FEM Simulation for Cold Rolling of Plate and Strip
- 中北大学学报（自然科学版） 2009年30卷第4期页码：390-394
- 作者机构：
  
  太原科技大学材料科学与工程学院
- 作者简介：
- 基金信息：
- DOI：
  中图分类号：
- 纸质出版：2009
- 稿件说明：
移动端阅览
张雅琴, 何宗霖, 张雪娜. 板带冷轧过程三维弹塑性有限元模拟[J]. 中北大学学报（自然科学版）, 2009,30(4):390-394.

张雅琴, 何宗霖, 张雪娜. Three-Dimensional Elastic-Plastic FEM Simulation for Cold Rolling of Plate and Strip[J]. 2009, 30(4): 390-394.
张雅琴, 何宗霖, 张雪娜. 板带冷轧过程三维弹塑性有限元模拟[J]. 中北大学学报（自然科学版）, 2009,30(4):390-394. DOI：

张雅琴, 何宗霖, 张雪娜. Three-Dimensional Elastic-Plastic FEM Simulation for Cold Rolling of Plate and Strip[J]. 2009, 30(4): 390-394. DOI：

摘要

在总结以往板带冷轧有限元分析的基础上

综合考虑了轧辊和轧件的接触与耦合变形问题

采用改进的离散化方法

建立了四辊三维弹塑性板带冷轧计算模型.利用所建立的模型对带钢轧制过程轧件的残余应力、变形以及张力对板凸度和压下量的影响进行了模拟分析

模拟结果与实验结果的比较证明所建立的模型是正确的.研究方法与结果为有限元技术在板带冷轧研究方面的应用提供了一条有效途径.

Abstract

Based on the FEM analysis for cold rolling of plate and strip carried by former researchers

the four-high three-dimensional elastic-plastic FEM models were established.The contact and coupling deformation problems of rolls and rolled piece were considered as a whole and an improved discretization method was used in the modeling process.The residual stress and deformation of the piece as well as the influences of tension on the crown and screw-down were analyzed by using the models.The comparison of simulation results and experimental data prove that the FEM models are accurate and reliable.The method and calculation results offer an effective way for the application of FEM in the study of cold rolling process of plate and strip.

关键词

Keywords

references

Yu Hailiang,Liu Xianghua,Wang Chao,et al.Analysis of roll gap pressure in sendzimir mill by FEM[J].Journalof Iron and Steel Research International,2008,15(1):30-33.

Liu Xianghua,Shi Xu,Li Shanqing,et al.FEM analysis of rolling pressure along strip width in cold rolling process[J].Journal of Iron and Steel Research International,2007,14(5):22-26.

王新洲,付兴,时旭,等.四辊轧机辊系压扁的有限元分析[J].塑性工程学报,2006,13(6):83-86.Wang Xinzhou,Fu Xing,Shi Xu,et al.FEM analysis for roll flattening in thin strip rolling[J].Journal of PlasticityEngineering,2006,13(6):83-86.(in Chinese)

谢红飙,肖宏,张国民,等.显示动力学有限元法分析板宽对板带轧制压力分布的影响[J].塑性工程学报,2003,10(1):61-66.Xix Hongbiao,Xiao Hong,Zhang Guomin,et al.Analysis of strip rolling pressure distribution for different width byexplicit dynamic FEM[J].Journal of Plasticity Engineering,2003,10(1):61-66.(in Chinese)

Yuan Siyu,Zhang Liwen,Liao Shulun,et al.3D FE analysis of thermal behavior of billet in rod and wire hotcontinuous rolling process[J].Journal of Iron and Steel Research International,2007,14(1):29-32.

Guo Zhongfeng,Li Changsheng,Xu Jianzhong,et al.Analysis of temperature field and thermal crown of roll duringhot rolling by simplified FEM[J].Journal of Iron and Steel Research International,2006,13(6):27-30.

Yu Hailiang,Liu Xianghua,Zhao Xianming,et al.Explicit dynamic FEM analysis of multipass vertical-horizontalrolling[J].Journal of Iron and Steel Research International,2006,13(3):26-30.

Jiang Z Y,Tieu A K,Zhang X M.Finite element simulation of cold rolling of thin strip[J].Journal of MaterialsProcessing Technology,2003,140:542-547.

刘立忠,刘相华,王国栋.轧制过程的显式动力学有限元模拟[J].东北大学学报,2001,22(3):327-330.Liu Lizhong,Liu Xianghua,Wang Guodong.Simulation on the strip rolling by dynamic explicit FEM[J].Journal ofNortheastern University,2001,22(3):327-330.(in Chinese)

赵丽丽,张以都.基于MSC的板材冷轧残余应力分布的数值仿真[J].有色金属,2005,57(1):27-29.Zhao Lili,Zhang Yidu.Residual stress numerical simulation of cold rolling board based on MSC[J].NonferrousMetals,2005,57(1):27-29.(in Chinese)

刘华,杨荃,何安瑞.张力对大宽厚比铝箔板形的影响[J].塑性工程学报,2005,12(4):62-65.Liu Hua,Yang Quan,He Anru.Influence of tension on Aluminum foil profile under large width to thickness ratio[J].Journal of Plasticity Engineering,2005,12(4):62-65.(in Chinese)

徐致让,薛家国.四辊轧机辊形变形分析的有限元方法[J].力学与实践,2000,22(5):22-27.Xu Zhirang,Xue Jiaguo.Finite element method for the analysis of rolls deflection for 4-high mill[J].Mechanics inEngineering,2000,22(5):22-27.(in Chinese)

孙林,张清东,陈先霖,等.中板轧机板形控制性能的研究[J].钢铁,2002,37(1):34-38.Sun Lin,Zhang Qingdong,Chen Xianlin,et al.Research on profile and flatness control characteristics of plate mill[J].Iron and Steel,2002,37(1):34-38.(in Chinese)

时旭,刘相华,王国栋,等.四辊冷轧机轧辊弯曲和压扁变形的有限元分析[J].东北大学学报,2004,25(10):957-960.Shi Xu,Liu Xianghua,Wang Guodong,et al.FEM analysis for roll deformation of a 4-high cold strip mill[J].Journal of Northeastern University,2004,25(10):957-960.(in Chinese)

陈火红.Marc有限元实例分析教程[M].北京:机械工业出版社,2002:1-11.

浏览量

428

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

发动机活塞CAD系统研究

影响函数在火箭弹内力和变形计算中的应用

钨柱杀爆弹固定套变形机理研究

超重力强化氢氧化钾耦合甘氨酸钾溶液脱除密闭空间CO2的研究

基于可重构创新散件的并联机器人实验平台设计